Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Just how do you actually feel in relation to Installing A Bathtub?
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate easily; if you have to open up a wall surface to remove the old tub and place the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will require an assistant to vacate the old bathtub and also set in the new one. Make sure you have certified on your own for the job and also are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed project, it is better to think about using one prior to you start. Chances are you may need a professional plumber to make tube links.
This post will certainly help you install a new bathtub in your restroom if you have already purchased a new tub and also do not require to transform the setup of your previous supply of water pipes.
Your devices and product list ought to make up the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted access that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. Once the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the level reads degree.
To set up taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water and examine all joints as well as new pipework for leakages and also tighten them if necessary. Load the bathtub as well as also check the overflow electrical outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used at the very least once as this will settle it into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in location in between the faucet and also the sink. Protect the faucet in position with the supplier provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, resulting in problems with wetness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about Tools You Need to Install a New Bathtub , I was thinking sharing that excerpt was really useful. Sharing is nice. Helping others is fun. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Visit Our Website Report this page